Crown XLS5000D
 

Crown XLS5000D (Crown XLS 5000D)

The XLS Series of power amplifiers from Crown represents a new era in affordable, quality power amplification.

XLS Series amplifiers are professional stereo power amplifiers engineered to meet demanding audio requirements - reliably and within budget. Every XLR Series amplifier is backed by Crown's unequaled three-year, no-fault, fully transferable warranty that covers everything.

With over five decades of experience designing and building rock-solid products, Crown is the standard in amplifier technology. So check out the affordable Crown XLS Series.

Features

• Reliable design incorporates many popular features
• Housed in a rugged, all-steel 3U chassis
• Efficient forced-air fans prevent excessive thermal buildup
• Electronically balanced XLR inputs; touch-proof binding post and Speakon outputs
• Precision detented level controls, power switch, power LED, and six LEDs which indicate signal, clip and fault for each channel
• Three-year, no-fault, fully transferable warranty completely protects yourinvestment and guarantees its specifications

Output Power (1kHz continuous average power with 0.1% THD)

• 2 ohm stereo (per channel): 2,500W (with 1% THD)
• 4 ohm stereo (per channel): 1,800W
• 8 ohm stereo (per channel): 1,100W
• 8 ohm bridge mono: 3,600W
• 4 ohm bridge mono: 5,000W (with 1% THD)

Performance

• Sensitivity (for full rated power at 4 ohms): 1.25 Vrms.
• Frequency Response (at 1 watt, 22 Hz to 20 kHz): +0 dB, –1 dB.
• Signal-to-Noise Ratio (20 Hz to 20 kHz, inputs terminated): A-weighted, below rated power: > 100 dB. No weighting, below rated power: > 95 dB.
• Total Harmonic Distortion (THD): < 0.5%.
• Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%.
• Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.
• Crosstalk (below rated power): at 1 kHz: –75 dB. at 20 kHz: –59 dB.
• Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced.
• Load Impedance: 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono.
• AC Line Voltage and Frequency Confi gurations Available (±10%): 120 VAC 60Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC.

Controls

• Level: Two front-panel rotary level controls, one for each channel.
• Power: Front-panel switch; on when in the IN position.
• Circuit Breaker: Back-panel breaker provides overload protection.
• Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode.

Indicators

• Signal Presence Indicators: Two green LEDs, one for each channel, illuminate when the channel’s input signal exceeds –40 dBu.
• Clip Indicators: Two red LEDs, one for each channel, illuminate when the channel’s output is being overdriven.
• Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available.
• Fault Indicator: Two red LEDs, one for each channel, illuminate whenamplifier is in protect mode. Also illuminates briefl y during normal power-upwhen amplifier is first switched on.

Input/Output

• Input Connectors: One per channel; back-panel three-pin female XLR input connectors.
• Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or4-pole Speakon® connectors. The top Speakon connector is wired for bothchannels so it can be used for bridge-mono wiring or for stereo wiring of twospeakers to a single Speakon connector.
  One pair of back-panel bindingposts per channel; accepts banana plugs or bare wire. (European models do notaccept banana plugs.)

Protection

• XLS Series amplifiers provide extensive protection and diagnosticcapabilities, including output current limiting, DC protection, circuitbreaker, and thermal protection.

Construction

• Ventilation: Flow-through ventilation from front to back.
• Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.
• Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³).
• Dimensions (W x H x D): 19" x 5.25" x 15.5"
• Weight: 62 lbs net; 74 lbs shipping

5 Seconds Can Save You 15% or More on DJ Equipment!