Crown XTI2002
Amplifier: 800W x2 at 4 Ohms - DISCONTINUED

product discontinued

This product has been discontinued by the manufacturer. Please contact us to find a replacement.


  XTi-1002 XTi-2002 XTi-4002 XTi-6002
2Ω Stereo (per ch.) 700W 1000W 1600W 3000W
4Ω Stereo (per ch.) 500W 800W 1200W 2100W
8Ω Stereo (per ch.) 275W 475W 650W 1200W
8Ω Bridge-Mono 1000W 1600W 2400W 4200W
4Ω Bridge-Mono 1400W 2000W 3200W 6000W

Crown XTI 2002

The Crown XTi Series
There's no debate – when you choose Crown's XTi 2 Series, you're choosing one of the most powerful and innovative amplifiers on the market today. That's because the all-new XTi 2 Series amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.

Next Generation Features

Peakx Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
New system monitoring provides software visibility of AC line voltage and power supply temperature
Integrated cast-aluminum handles for easy handling and enhanced durability
Locking power cord clip provides a secure connection between the amplifier and power cord
Updated HiQnet System Architect™ control software
Increased number of presets to a total of 50; 49 of which are user definable

Crown's Integrated Processing

Input EQ
6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.

Crossover Filters
Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.

Output EQ
8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.

For signal alignment of driver; 50 mS of total delay.

SubHarmonic Synth
Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.

Peakx Plus Limiter
User defeatable limiter that allows users to control Threshold, Attack, and Release times.

50 total presets, 49 of which are user-definable.

The XTI Series Performance

Sensitivity (for full rated power at 4 ohms)
1.4 Vrms

Frequency Response (at 1 watt, 20 Hz - 20 kHz)
+0 dB, –1 dB

Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms)
XTi1002/2002/4002: 100 dB (A weighted)
XTi6002: 103 dB (A weighted)

Total Harmonic Distortion (THD)
< 0.5%

Damping Factor 20 Hz to 1 kHz
> 500

Crosstalk (below rated power)
20 kHz - 1 kHz: > 70 db

Input Impedance (nominal)
20k ohms balanced, 10k ohms unbalanced

Maximum Input Signal
+22 dBu typical

AC Line Voltage and Frequency Configurations
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz

AC Line Current
(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)

XTi1002: 6.8A; no more than 38W at idle
XTi2002: 8.3A; no more than 38W at idle
XTi4002: 10.5A; no more than 38W at idle
XTi6002: 15.3A; no more than 180W at idle

Operating Temperature
0°C to 40°C at 95% relative humidity (non-condensing)

Controlling your Crown XTI Amplifier

Two front-panel rotary level controls, one for each channel

Power Switch
On/Off switch applies AC power to the amplifier

Sel/Prev/Next Buttons
Three buttons near the LCD screen that are used to access menu items and front panel lockout

LCD Screen
Backlit liquid crystal display that shows preset and processing status

The In's and Out's on the XTI Series

Input Connectors
XLR, one per channel

Link/Out Connector
Loop-thru signal from input connector for linking another amplifier, one per channel.

Output Connectors
Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).

HiQnet USB Connector
Type B, connects to HiQnet network.

Crown XTi Series Amplifier Construction


Front Panel

Proportional speed fan with front-to-rear airflow.

XTi 1002/2002/4002: 19" (W) x 3.5" (H) x 12.25" (D)
XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D)

Net Weight
XTi 1002/2002/4002: 18.5 lbs (8.4kg)
XTi 6002: 24.0 lbs (10.9kg)

Shipping Weight
XTi 1002/2002/4002: 21.5 lbs (9.8kg)
XTi 6002: 30.0 lbs (13.6kg)

Option #1 - Affirm Financing

Order Value Term Length APR
$50-699.99 3, 6 or 12 Months Interest-Bearing
$700+ 3, 6 Months 0% (Qualified Customers)
3, 6, 12 or 18 Months Interest-Bearing
  • -Upon Checkout, click Affirm
  • -Get approved in seconds
  • -No late fees

Option #2 - Lease Financing

Option #3 - Business Lease Financing

Option #4 - Free Lay-Away Program

  • -Call 877-775-7635 to get started
  • -No credit checks, no late fees, no minimum order
  • -Pay when you can & we'll ship when it's paid off
  • -FREE to use ($10 initial charge is applied to final payment)
DJ & AUDIO > Mixers, Amps & Processing > Amplifiers & Powered Mixers
UPC: 871015005317
Brand: Crown

Other similar products



Yamaha EMX7


QSC RMX2450a